In a simple series circuit, the total voltage is shared among resistors in proportion to their resistance. For a 30 V source with 10 Ω and 20 Ω in series, the current is 1 A and the 10 Ω resistor drops 10 V. This builds intuition for how signals and power flow in avionics wiring.

Multiple Choice

In a circuit with an applied voltage of 30 volts, what is the voltage drop across a 10-ohm resistor in series with a 20-ohm resistor?

To determine the voltage drop across a specific resistor in a series circuit, it is essential to understand how voltage divides among the resistors. When resistors are connected in series, the total voltage across the circuit is divided among the resistors in proportion to their resistances. In this case, you have a circuit with a total applied voltage of 30 volts, consisting of a 10-ohm resistor and a 20-ohm resistor in series. The total resistance of the circuit can be calculated by adding the individual resistances together: Total resistance, \( R_{total} = R_1 + R_2 = 10 \, \Omega + 20 \, \Omega = 30 \, \Omega \). Next, you find the current flowing through the circuit using Ohm's Law, which states that \( V = I \times R \). Rearranging it gives \( I = \frac{V}{R} \): Current, \( I = \frac{30 \, V}{30 \, \Omega} = 1 \, A \). Now that you have the current, you can find the voltage drop across the 10-ohm resistor using Ohm's Law again: Voltage drop across

When you wire two resistors in a line, think of them as two water hoses sharing the same trickle of pressure. The voltage is the pressure, and the current is the flow. In a series arrangement, that pressure finds its own path through each resistor, and the way it splits isn’t by a guess. It’s fixed by how much resistance each limb offers. In aviation electronics, where you’re often diagnosing a mysterious voltage drop or a flaky sensor, understanding this simple idea—voltage division—can save you hours of head-scratching.

Let’s set up a clean picture. Suppose you’ve got a 30-volt source in a small avionics circuit, and it feeds a 10-ohm resistor in series with a 20-ohm resistor. Both resistors share the same current because they’re in a single loop. The big lesson here is this: the current is the same through all components in a series circuit, but the voltage drop across each component depends on its resistance.

First, total resistance. When resistors sit in series, their resistances add up. So R_total = 10 ohms + 20 ohms = 30 ohms. This feels almost too neat, but it’s exactly how DC circuits behave: the series path is a single path, so the total resistance is just the sum.

Next, the current. Ohm’s Law is your go-to workhorse: V = I × R. With a 30-volt supply and 30 ohms total, the current I is 30 V / 30 Ω = 1 A. One amp flowing through the chain—nice and tidy.

Now for the voltage drop across each resistor. The rule in a series circuit is straightforward: the voltage drop across a given resistor is I × R for that resistor. Since the current is 1 A, the drop across the 10-ohm resistor is V = I × R = 1 A × 10 Ω = 10 V. That means the remaining voltage—what’s left for the other resistor—is 30 V − 10 V = 20 V. And indeed, the 20-ohm resistor would drop 1 A × 20 Ω = 20 V. The numbers line up perfectly, which is always a nice sanity check.

But let’s pause and pull this into something more tangible, especially for avionics work. In an airplane, you’re often dealing with DC power distribution, sensors, actuators, and conditioning circuits where the exact voltage each leg sees matters a lot. If a sensor relies on a specific biasing network or if a signal path spills over into a different DC level, you want to know how the supply’s 30 V is apportioned along the chain. Voltage division is the language you use to predict that allocation before you power up.

A practical way to see this is to imagine a simple voltage divider you might encounter in a sensor interface. Not every part of the circuit needs to take the same voltage; the important thing is that the current remains steady through series elements. In aviation, this thinking helps when you’re diagnosing a mysterious drop that causes a gauge to read low or a control head to misbehave. If one leg of the divider is dragging the voltage down more than expected, you can pinpoint it by checking which resistor is hogging the voltage.

Let me explain with a quick mental checklist you can apply on the shop floor or in the lab.

  • Confirm the topology. In a series chain, current is the same through all components. If you’re seeing different currents in different parts of a circuit, you’re probably not in a pure series setup.

  • Add up the resistances. R_total is the simple sum. If you’re not sure about what you’re looking at, redraw a tiny schematic. It helps to label each element and its value.

  • Compute the current first. Use I = V / R_total. If you know the input voltage and the total resistance, this is your starting point.

  • Allocate voltage drop by proportion. The voltage across a resistor in a series chain is proportional to its resistance. Larger resistance gets a larger share of the voltage, smaller resistance gets less.

  • Check with a quick sanity test. Multiply the current by each resistance to verify the drops add to the total supply. It’s a fast way to catch a misread or a misplaced component.

You might be wondering: what about real-world tolerances? Resistors aren’t ideal. They have a tolerance band, say ±1%, ±5%, or ±10%. In a tight avionics subsystem where precision matters, those tolerances can tip the voltage slightly, especially if you’re nearing a power-sensitive threshold. A 1% resistor isn’t a dramatic deviation, but in a delicate signal path, even a few tenths of a volt can shift an ADC reading or push a transistor slightly out of its comfortable operating region. So while the math gives you the ideal picture, you also learn to factor in those little deviations and then design around them—perhaps with tighter tolerance parts or by placing sensitive components in a way that helps maintain stability.

Another useful angle is to connect this concept to the broader world of power distribution in aircraft. Modern avionics bays are full of feeds from 28 V or 30 V DC buses, with buses feeding an assortment of modules, fans, sensors, and interface devices. In many of those circuits, you’ll encounter resistive networks that shape voltages or bias levels. The idea that a voltage source “splits” its impact across components in proportion to their resistance is a recurring theme. It’s the same principle behind why a simple LED with the right resistor glows gently instead of screaming bright; the resistor tames the current so the LED’s forward voltage isn’t blasted beyond its sweet spot.

If you fancy a quick mental exercise to keep this in your mental toolbox, consider swapping out the numbers. What if you had a 30 V supply feeding a 5-ohm and a 25-ohm resistor in series? The total resistance is 30 ohms, so the current is 30 V / 30 Ω = 1 A again. The drop across the 5-ohm resistor would be 1 A × 5 Ω = 5 V, and across the 25-ohm resistor it would be 1 A × 25 Ω = 25 V. Notice how the voltage division shifts with the resistances—yet the total still bridges the full 30 V. That intuition is exactly what helps you troubleshoot and reason about existing hardware in the field.

Now, a practical tangent you’ll likely appreciate: how do you verify this in hardware without breaking your flow? A multimeter set to DC voltage mode is your ally. With the circuit de-energized, you can measure the resistance of each leg. When you reapply a known supply (preferably with the power off and only during safe testing), you can compare the measured voltage drops with the calculated values. If the numbers don’t align, you’ve got a clue where things aren’t behaving as the simple series model predicts. Maybe a component is out of tolerance, or there’s an unintended parallel path leaking current, or a wiring fault is inserting an extra resistance in the path. The moment you spot a discrepancy, you’ve narrowed the field dramatically.

In these scenarios, it’s also worth considering the role of temperature. Resistances drift a little with heat. In avionics enclosures, under load, resistors can warm up, and that warmth can nudge the voltage distribution slightly. Designers account for that by choosing resistors with suitable wattage ratings and, sometimes, by decoupling sensitive nodes from heavy loads with separate regulation schemes. The upshot is: simple math gives you the baseline, and real-world conditions refine your understanding.

Let’s circle back to the original setup and cement the takeaway. With 30 volts total, a 10-ohm resistor in series with a 20-ohm resistor shares the voltage in proportion to its resistance. The current in the loop is 1 amp, the same everywhere along the chain. Multiply the current by each resistor’s value, and you get the voltage drops: 10 V across the 10-ohm resistor and 20 V across the 20-ohm resistor. The math isn’t just abstract; it’s the blueprint for predicting how a circuit behaves under fault-free conditions and, more importantly, for spotting when something’s off.

A few closing thoughts that resonate in the aviation world. When you’re wiring, testing, or repairing avionics, you’re often balancing reliability, safety, and performance. The humble voltage divider is more than a textbook example; it’s a practical lens for understanding how power flows, where losses occur, and how to diagnose anomalies without tearing the system apart. And because aviation electronics live in a high-stakes environment, the habit of checking the basics—the series flow, the total resistance, the current, and the voltage drops—becomes a form of due diligence you can trust.

If you ever find yourself staring at a schematic and a handful of color-coded resistors, remember this: the circuit is telling a story. The numbers aren’t random. They map out a clean path for the current, and they reveal how the pressure of the supply is allocated across each leg. In that story, the 10-ohm resistor doesn’t just sit there; it claims its 10-volt share, and the 20-ohm resistor takes the remaining 20 volts. It’s a small, elegant balance, and it’s at the heart of how dependable avionics circuits stay steady under demanding conditions.

So next time you’re untangling a stubborn circuit, start with the basics, respect the chain, and let the simple truths guide you. Voltage division in series isn’t just a calculation—it’s a practical, everyday tool for making sense of the hardware you trust with critical tasks every day. And that little 10-volt drop? It’s a reminder that even in complex avionics systems, clarity often begins with understanding the simplest rules.